A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
Just how do you feel about How to Install a Bathtub Yourself?
Installing a bath tub isn't specifically brain surgery, but it does need solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old tub with a new one is also a moderately hard task. If the old tub is conveniently available, the project can move speedily; if you need to open a wall surface to eliminate the old bathtub and position the new bath tub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and set in the new one. Make sure you have certified yourself for the job and also fit trying it. Instead of hiring a professional to take control of a halfway-completed task, it is far better to consider utilizing one before you start. Opportunities are you may require an expert plumber to make tube connections.
This write-up will aid you mount a brand-new bathtub in your restroom if you have actually currently acquired a brand-new tub and also don't require to alter the setup of your previous water system pipelines.
Your devices and product list ought to make up the following:
Planning for the Installation
Firstly, the supporting framework provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the restricted gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the staying water that will come from the pipes. Once the supply pipes have been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. Once the taps have been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the tub in the required position. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the level reads level.
To set up faucets, fit all-time low of the outermost flexible tap adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the supply of water and also examine all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub and also examine the overflow electrical outlet and the regular outlet for leaks.
Finally, deal with the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub needs to wait until the bathtub has actually been utilized a minimum of once as this will certainly settle it right into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in area between the tap as well as the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type must be attached to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a stiff seal, triggering the water to pass through the wall in between the bath as well as the tiling, causing difficulties with dampness and possible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to permit the activity experienced when the tub remains in usage. The sealant can crack relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly readily available on the market. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about Installing A Bathtub? Try to leave a short review further down. We'd be delighted to hear your opinion about this entry. In hopes to see you back again later on. Sharing is nice. You never know, you may just be helping someone out. Thanks so much for your time spent reading it.
Hire A Pro Report this page